“UbuntuHelp:WifiDocs/LinksysWPC54G”的版本间的差异
来自Ubuntu中文
小 |
小 |
||
第10行: | 第10行: | ||
Here is a step-by-step instruction, which workes very well on IBM Thinkpad with WPC54GS (BMC Chipset) card: | Here is a step-by-step instruction, which workes very well on IBM Thinkpad with WPC54GS (BMC Chipset) card: | ||
− | First, download [http://www.linksys.com/servlet/Satellite?c=L_CASupport_C2&childpagename=US%2FLayout&cid=1166859842300&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=4230058334B317&displaypage=download | + | First, download [http://www.linksys.com/servlet/Satellite?c=L_CASupport_C2&childpagename=US%2FLayout&cid=1166859842300&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=4230058334B317&displaypage=download the non-free drivers]. Unzip the drivers somewhere in your home-directory. |
Then install bcm43xx-fwcutter and use it to get the firmware stuff needed for ndiswrapper: | Then install bcm43xx-fwcutter and use it to get the firmware stuff needed for ndiswrapper: | ||
<pre><nowiki> | <pre><nowiki> | ||
第41行: | 第41行: | ||
</nowiki></pre> | </nowiki></pre> | ||
Wait until dhcp gets it's stuff and then test it (browse google) | Wait until dhcp gets it's stuff and then test it (browse google) | ||
− | + | ---- | |
+ | [[category:CategoryCleanup]] [[category:CategoryHardware]] | ||
[[category:UbuntuHelp]] | [[category:UbuntuHelp]] |
2008年10月19日 (日) 18:11的版本
点击翻译: |
English |
请不要直接编辑翻译本页,本页将定期与来源同步。 |
This How To explains the setup of Linksys cards that require the ndiswrapper module. Follow these steps:
- Link to ndis page Ndiswrapper
These instructions for Debian have been helpful for several people configuring linksys cards Arthur's homepage: using WPC54G with Debian
- The Linksys WPC11 ver 4 is a confirmed success.
- In one case at least, manually entering nameserver information into /etc/resolv.conf was required.
Here is a step-by-step instruction, which workes very well on IBM Thinkpad with WPC54GS (BMC Chipset) card: First, download the non-free drivers. Unzip the drivers somewhere in your home-directory. Then install bcm43xx-fwcutter and use it to get the firmware stuff needed for ndiswrapper:
apt-get install bcm43xx-fwcutter ndiswrapper-utils-1.8 ndiswrapper-common cd ~/windows_drivers/ bcm43xx-fwcutter bcmwl5.sys cp bcm43xx* /lib/firmware modprobe ndiswrapper ndiswrapper -i bcmwl5.inf ndiswrapper -l
Depending on the driver package used, bcmwl5.inf and bcmwl5.sys can be on different places in the subdirectories... should show the following:
bcmwl5 driver installed, hardware present
Then edit /etc/network/interfaces to contain the following. Alternatively you can just use the gnome or kde configuration tools:
auto eth1 iface eth1 inet dhcp wireless-essid linksysgabba wireless-key 0A0A0A0A0A0A0A0A0A0A0A
Of course you use your ESSID and WEP-KEY then ;-) As next, you take up the interface:
ifdown eth0 ifdown eth1 ifup eth1
Wait until dhcp gets it's stuff and then test it (browse google)